Why We Built the B250CC
Repeated pulling and tight desk setups can force a cable into sharp bends, placing extra stress on the connection between the connector and cable.
Reinforced where cables bend most
The reinforced strain-relief area helps distribute everyday bending and pulling near the connector.
Reliable power for a cleaner desk setup
With support for up to 240W charging and 40Mbps data transfer, the B250CC is designed for compatible USB-C devices used at work and at home.
Four Features That Make the B250CC More Reliable for Everyday Charging

SUNGUY 240W USB-C to USB-C Charging Cable B250CC
Choose Amazon for individual retail orders or Alibaba for bulk and business purchasing.
Pros & Cons
- Supports up to 240W charging with compatible USB-C devices and chargers.
- Reinforced strain relief and a braided exterior help handle repeated bending and pulling.
- Supports everyday data transfer at speeds of up to 40Mbps.
- 240W charging requires a compatible charger and device.
- Designed for USB-C to USB-C connections only.
- Up to 40Mbps data transfer is intended for basic file syncing rather than high-speed transfer needs.
Reliability Tested for Stable Performance
Swing Test ≥10K Cycles
Test Requirements:
- The strain relief (SR) must extend at least 5 mm above the bottom of the clamping fixture. The cable must not come into contact with the fixture during the swing test (90° rounded corner radius of the fixture: ≤12.7 mm).
- The test weight must be positioned 30 cm below the bottom of the clamping fixture. If the cable is not long enough, an extension cable may be used.
- Standard Data Cables: 300 g load, ±90° (180° total), 30 cycles per minute, for 10,000 cycles.
- 1-to-N Multi-Connector Cables: Clamp the central junction and test both the main cable and branch cables with a 300 g load at ±60° (120° total) for 3,000 cycles. One complete back-and-forth movement counts as one cycle.
- Functional inspection: Charging and data transmission must remain normal after testing and after the SR is slowly bent 90° in four directions.
- Sample requirement: Test 6 pcs per batch; all 6 must pass with no jacket damage, cracks, exposed wires, or other visible abnormalities.
- Test equipment: Cable Swing Test Machine (Cable Flexing Tester).
Tensile Load Test ≥10 kg
Test Requirements:
- Standard tensile load test: Apply a static 10 kg load between the connector and cable for 1 minute.
- The internal wires must not break, and charging, data transmission, and tensile performance must remain normal.
- SR with cable retention clip: Apply a static 3 kg load to the retention clip in the direction of the connector for 1 minute to simulate cable-retraction impact.
- The internal wires must remain intact, charging and data upload/download must remain normal, and cable elongation must not exceed 2 mm.
- After disassembly, any crimped connection must remain securely attached without detachment.
- Test equipment: Tensile Load Testing Machine.
Insertion & Withdrawal Test ≥10,000 Cycles
Test Requirements:
- Insert and withdraw the male connector from the corresponding female receptacle at 20 cycles per minute.
- USB Type-C / Lightning / Micro USB: 10,000 cycles. USB Type-A: 5,000 cycles.
- Initial insertion and withdrawal force for Type-C / Lightning / Micro USB / USB-A: 8–18 N.
- After testing, insertion and withdrawal force must remain within 8–20 N.
- USB Type-C contact pin height after 10,000 cycles must be ≥0.18 mm.
- Charging and data transmission must remain normal after testing.
- Test equipment: Connector Insertion and Withdrawal Testing Machine.
Salt Spray Test ≥48 Hours
Test Conditions and Procedure:
- Position samples at an upward-facing angle of 15°–30° and avoid solution accumulation.
- Chamber temperature: 35 ± 2°C. Salt solution: 5.0 ± 1% NaCl. pH: 6.5–7.2.
- Using an 80 cm² collection area over 16 consecutive hours, maintain an average collection rate of 1.0–2.0 mL/hour across all exposed areas.
- After testing, rinse under running tap water for 5 minutes, then rinse with distilled or deionized water. Remove droplets and allow samples to stand for 1–2 hours.
- Exposure duration: Standard cables: 48 hours. Cable assemblies: 24 hours.
- Acceptance: Fewer than 3 corrosion spots on nickel-plated components and fewer than 5 on gold-plated components; no structural damage, deformation, melting, oil exudation, exposed wires, or broken conductors.
- USB Type-A: No visible corrosion after 24 hours. After 48 hours, corrosion is permitted only at crimped joints and cut edges, with no more than 3 spots per connector, edge corrosion no longer than 2 mm, and each spot smaller than 1 × 1 mm.
- Test equipment: Salt Spray Test Chamber.
View the Full Performance Test Report
The B250CC was evaluated through swing, tensile-load, connector insertion and withdrawal, and salt-spray testing. For detailed test conditions, procedures, cycle counts, and acceptance criteria, view the complete B250CC performance test report.







